PowerPuck II

EIT PowerPuck II

• Used in curing applications of inks, adhesives, soldermasks, and epoxies (not for use in web press applications)
• Incorporates 4 separate spectral response ranges and measures all 4 simultaneously
• Easy to read data display of all 4 bands. Data collected for all 4 bands is displayed simultaneously on screen in mW/cm2 and mJ/cm2 for quick and easy viewing by the operator. No need to toggle through all eight readings one at a time.
• Graph Mode - A graph illustrating the collected UV irradiance and energy is displayed for each of the 4 UV bands. Data is expressed in mW/cm2 vs. time.
• Measures UV lamp performance (and possible bandwidth shift for doped lamps)
• Compares the efficiencies of different UV curing systems.
• See Brochure

PowerMap

EIT PowerMap Plus

• "Records" the UV intensity and temperature throughout a UV curing system
• Simultaneously measures peak power density and total energy density in four spectral regions
• Uses 4 UV detectors (UVA, UVB, UVC and UVV visible)
• Provides the user with a graphic profile of each part of the UV spectrum..
• Supplied with Windows based PowerView software.
• Adjustable sampling rate from 128 to 2048Hz.
• Use high sampling rate to view lamp and power supply stability
• Provides an excellent analysis of any UV curing system.
• Provides solid SPC information.
• Brochure and specifications.
• See example screen shots of PowerView Software.

Micro Cure

EIT MicroCure

• Microprocessor based, battery powered miniature UV radiometer
• Small Size: 33.0mm x 25.4mm x 6.4mm
• Designed to measure UV dose in web printing, container curing, any tight access UV curing application
• Fast sample rate - 2000 per second


• technical specifications: specifications
  
  

3D

EIT 3D Sensor

• Multiple measurement points - up to 32 sensors!
• Small, low profile Sensor with cosine response, each calibrated and serialized.
• Individual Sensors are single band and are available in any of EIT's four standard (UVA, UVB, UVC or UVV) bandwidths. The sensors can be combined in any combination of bandwidths to meet the measurement needs of your UV source(s) and process.
• Sensors are easily attached on either a permanent or a temporary basis.
• Flexible daisy-chained quick connector system allows the Sensors to be placed exactly where they are needed without creating an octopus maze of cables.
• An LED on each Sensor can be toggled via software to easily identify its location on the work piece.
• See Brochure

Compact Sensor

EIT Compact Sensor

• Improved optical design to virtually eliminate solarization
• Small profile for installation in tight spaces
• Squared body design for easier mounting
• Can be used on most lamp makes and types
• Sealed optics to prevent contamination - optional air purge
• Available with a "lamp on" detector
• Compatible with any of EIT¹s monitoring equipment
• (Must be powered by MultiBrite or Online Display or DIN Rail.)

Download pdf of this brochure

  Which On-Line Lamp Monitoring Systems Should I Use?

MultiBrite Sensor

EIT Multibrite

• Continuously monitors up to four UV lamps simultaneously
• Provides a readout in percentage of 100% original UV lamp output
• Incorporates a 0-10V output and 4-20mA current output proportional to UV
• Sounds an alarm when any lamp falls below a user settable low limit threshold
• Powered by 110V or 220V

Download pdf of this brochure

ON-line Display

EIT ONLINE UV INTENSITY DISPLAY MODULE

• Continuously monitors the output of a single UV lamp
• Displays results as a percentage of 100% original value
• Provides a 0-10 volt output proportional to UV which can interface to a PLC, strip chart recorder, etc.
• Provides an alarm relay contact
• Powered by 24 volts AC or DC

Download pdf of this brochure

DIN Rail monitor

EIT DIN Rail UV INTENSITY MONITOR

• Continuously monitors the output of a single UV lamp as a percentage of 100% original value
• Clamps onto "din rail" behind equipment allowing multiple units to be inserted into a relatively compact area
• Provides a 0-10 volts output proportional to UV which can interface to a PLC, strip chart recorder, etc.
• Features an alarm relay contact
• Powered by 24 volts AC or DC